Bilstein B12 Pro-Lift Kit Coilovers Ford Ranger 3 TKE 4WD 15+

Bilstein B12 Pro-Lift Kit for Ford Ranger 3 TKE 4WD (2015 onwards) – Raised Ride Height and Extra Ground Clearance

The Bilstein B12 Pro-Lift Kit raises the Ford Ranger 3 TKE 4WD above its standard ride height. It replaces the factory dampers and springs with Bilstein dampers and matched Eibach lift springs, adding ground clearance for rough tracks, tow-hitch use or simply a more rugged look.

Because the dampers are matched to the taller springs, the car keeps proper damping control instead of feeling floaty, as it would with spacers or lift springs alone. The kit is developed for this car and fits in place of the factory parts.

Performance

• Ride height: Approx 30 mm lift on both axles
• Damping: Fixed, tuned for this car
• Damper design: Monotube gas-pressure

Ride-height figures are Bilstein's application data for this part number, measured against the car's standard ride height. The actual change depends on the car's engine, equipment and the condition of the parts being replaced.

Key Features

• Raises ride height for extra ground clearance
• Bilstein dampers matched to Eibach lift springs
• Keeps controlled, predictable handling on the road
• Developed and tested for this specific car
• Direct replacement for the factory parts: no cutting or drilling
• Springs supplied with a parts certificate

What's in the Kit?

• 2 x front Bilstein dampers
• 2 x rear Bilstein dampers
• 2 x front Eibach lift springs
• 2 x rear Eibach lift springs

Please note: the photo shows a typical Bilstein B12 kit. The parts for your car are specific to it and will differ in appearance. Top mounts and fitting hardware are not included unless listed above.

Fitment

• Ford Ranger 3 TKE 4WD (2015 onwards)
• Engines: 2.0 EcoBlue, 2.2 TDCi
• Pickup
• 4x4 only

Not suitable for: cars with factory electronic damping or self-levelling suspension unless stated above; other generations, body styles or drivetrains not listed above.

Installation

Fitting replaces the dampers and springs at all four corners. Where the car has front struts, they must be dismantled with spring compressors to swap the springs. Check the top mounts, bearings and bump stops while everything is apart and replace any that are worn. Because the car sits higher, a four-wheel alignment is essential after fitting, and the headlight aim should be checked. We recommend professional fitting.

How do I check this fits my Ford Ranger?

This kit is for the Ford Ranger 3 TKE 4WD (2015 onwards). Check the details in the Fitment section, and if you're unsure, send us your registration or VIN and we'll confirm before you order.

How much will it raise my car?

Approx 30 mm lift on both axles, according to Bilstein's data for this part. The exact figure depends on your car's engine and equipment.

Can I fit this to a car with electronic or adaptive dampers?

This kit uses conventional dampers. If your car has factory electronic damping, check the Fitment notes above, as Bilstein makes separate DampTronic and EVO SE kits for many of these cars.

Do I need a wheel alignment after fitting?

Yes. Changing the ride height changes the suspension geometry, so a four-wheel alignment is needed after fitting. Let the springs settle for a few hundred miles first.

Is it road legal in the UK?

Yes, this kit is designed for road use. As with any suspension modification, you should tell your insurer once it has been fitted.

What type of dampers does it use?

Monotube gas-pressure, according to Bilstein's data for this part number. Gas-pressure dampers resist fading when they get hot during hard driving.

Is there a warranty?

Yes. Bilstein suspension is covered against defects in materials and workmanship. Contact us with your order number if you have any problem.

Do I need new top mounts?

They are not included. If your existing top mounts, bearings or bump stops are worn, replace them while the suspension is apart, as worn mounts can cause knocks and affect the alignment.