{"product_id":"st-x-coilovers-mini-cooper-se-f56-20-24","title":"ST X Coilovers Mini Cooper SE F56 20-24","description":"\u003ch2\u003eST X Coilovers for Mini Cooper SE F56 (2020-2024) – 25-45 mm Lower, Height Adjustable, Fixed Damping\u003c\/h2\u003e\n\u003cp\u003eThis ST X kit replaces the standard springs and dampers on the Mini Cooper SE F56 (2020-2024) with a height-adjustable coilover set. It lowers the car by approx. 25-45 mm at the front and 25-40 mm at the rear, which sharpens the steering, cuts body roll and closes up the wheel arch gap. The ride height is set on threaded struts, so you can go for a subtle drop or use the full approved range, and change it again later.\u003c\/p\u003e\n\u003cp\u003eThe ST X is the entry point to the ST range. It is built around a damper setting that ST have matched to this specific car, so there is nothing to adjust beyond ride height. Shaped (progressive) springs keep the ride compliant over small bumps and firm up as the suspension compresses, which makes it a good fit for a daily driver that needs to look lower and feel tighter without becoming harsh. ST is part of the KW automotive group, and the kit is developed and made in Germany using KW engineering.\u003c\/p\u003e\n\u003cp\u003eThis kit is for the Mini Cooper SE F56 (3-doors) with the Cooper SE \/ Electric, up to a 985 kg front axle load. Check the Fitment section below before ordering.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFront lowering:\u003c\/strong\u003e approx. 25-45 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRear lowering:\u003c\/strong\u003e approx. 25-40 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax front axle load:\u003c\/strong\u003e up to 985 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax rear axle load:\u003c\/strong\u003e up to 875 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight adjustment:\u003c\/strong\u003e Stepless, on threaded strut housings\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDamping:\u003c\/strong\u003e Fixed, pre-set by ST for this vehicle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSprings:\u003c\/strong\u003e Shaped progressive springs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStrut housings:\u003c\/strong\u003e Galvanised steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApproval:\u003c\/strong\u003e Parts type approval\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eLowering figures are ST's, measured against the standard car. The actual drop varies with engine, equipment and tolerances on each car, and the springs settle slightly after the first few hundred miles.\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eStepless ride height adjustment on a coarse, dirt-resistant trapezoidal thread\u003c\/li\u003e\n\u003cli\u003eDamper setting developed by ST for this vehicle, so no setup is needed beyond ride height\u003c\/li\u003e\n\u003cli\u003eShaped progressive springs for a comfortable ride with firmer support in corners\u003c\/li\u003e\n\u003cli\u003eGalvanised, multi-sealed steel strut housings for long-term corrosion protection\u003c\/li\u003e\n\u003cli\u003eComposite spring perches with stainless steel inserts that stay easy to adjust for years\u003c\/li\u003e\n\u003cli\u003eDust covers and bump stops protect the damper seals and act as an extra spring under heavy load\u003c\/li\u003e\n\u003cli\u003eDeveloped and built in Germany, based on KW engineering\u003c\/li\u003e\n\u003cli\u003eSupplied with a parts certificate and fitting instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's in the Kit?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e2 x height-adjustable front coilover struts with springs\u003c\/li\u003e\n\u003cli\u003e2 x rear dampers\u003c\/li\u003e\n\u003cli\u003e2 x rear springs with height-adjustable spring seats\u003c\/li\u003e\n\u003cli\u003eComposite spring perches with stainless steel inserts\u003c\/li\u003e\n\u003cli\u003eDust covers and bump stops\u003c\/li\u003e\n\u003cli\u003eParts certificate and fitting instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003ePlease note:\u003c\/strong\u003e the photos are for reference only and show a typical ST X kit. The exact struts, brackets and springs supplied depend on your car.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMini F56 (Dec 2013 on)\u003c\/li\u003e\n\u003cli\u003eEngines: Cooper SE \/ Electric\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNot suitable for:\u003c\/strong\u003e any vehicle not listed above. Contact us with your registration if you are unsure.\u003c\/p\u003e\n\u003ch3\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003eFitting means removing the original struts, springs and dampers and fitting the ST units in their place. We recommend a qualified workshop experienced with coilovers. A spring compressor is needed to strip down the original front struts. The original top mounts, bearings and fixings are reused, so check them for wear and replace any that are worn. Set the ride height within the approved range, tighten the suspension bolts with the car's weight on its wheels, and torque everything to the manufacturer's figures. A four-wheel alignment is required once the car is at its final ride height. Re-check the height and alignment after the first few hundred miles, once the springs have settled.\u003c\/p\u003e\n\u003cp\u003eDownload ST's documents for this kit: \u003ca href=\"https:\/\/docs.kwsuspension.de\/ea-STGFw-h2001038_200DP.pdf\" target=\"_blank\" rel=\"noopener\"\u003eFitting instructions (PDF)\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBefore you start:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eWith the factory wheels and tyres, wheel spacers may be needed to give enough clearance to the coilovers.\u003c\/li\u003e\n\u003cli\u003eOn the original wheel sizes, wheel spacers may be needed to keep enough clearance.\u003c\/li\u003e\n\u003cli\u003eThe original front dust covers are trimmed and reused, as shown in ST's instructions.\u003c\/li\u003e\n\u003cli\u003eDisconnect any ride height sensors (headlight levelling or self-levelling) before removing the old struts.\u003c\/li\u003e\n\u003cli\u003eClean the threads before adjusting, and start with the height adjusters in the middle of their range.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eAfter fitting:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eExpect the car to settle a further 5-10 mm once it has been driven, then re-check the height.\u003c\/li\u003e\n\u003cli\u003eCheck there is at least 5 mm clearance between the tyres and the suspension through the full steering and suspension travel.\u003c\/li\u003e\n\u003cli\u003eHave the headlight aim reset, along with any other height-dependent systems.\u003c\/li\u003e\n\u003cli\u003eESP\/ABS warning lights can appear after fitting. Some clear after a short drive, others need full steering lock both ways or a reset with a diagnostic tool.\u003c\/li\u003e\n\u003cli\u003eOn cars with radar or camera driver assistance systems, have the calibration checked after lowering.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUpgrade Further\u003c\/h3\u003e\n\u003cp\u003eWant to fine-tune the ride? The \u003ca href=\"\/products\/st-xa-coilovers-mini-cooper-se-f56-20-24\"\u003eST XA Coilovers Mini Cooper SE F56 20-24\u003c\/a\u003e adds 16-click rebound adjustment.\u003c\/p\u003e\n\u003cp\u003eFor rear camber adjustment, KW offer a vehicle-specific adjustable control arm set (part no. 68510131).\u003c\/p\u003e\n\u003ch3\u003eWill this fit my Mini Cooper SE F56?\u003c\/h3\u003e\n\u003cp\u003eIt fits the Mini Cooper SE F56 (2020-2024) with the Cooper SE \/ Electric. Check the Fitment section for the body styles and exclusions, or send us your registration and we will check.\u003c\/p\u003e\n\u003ch3\u003eHow low will my Mini Cooper SE F56 sit?\u003c\/h3\u003e\n\u003cp\u003eST quotes a drop of approx. 25-45 mm at the front and 25-40 mm at the rear compared with standard. The exact drop varies from car to car with engine, equipment and tolerances.\u003c\/p\u003e\n\u003ch3\u003eCan I adjust the damping?\u003c\/h3\u003e\n\u003cp\u003eNo, the damping is pre-set by ST to suit the springs, so there is nothing to set up. You only adjust the ride height. If you want adjustable damping, look at the ST XA.\u003c\/p\u003e\n\u003ch3\u003eWill the ST X make my Mini Cooper SE F56 ride harshly?\u003c\/h3\u003e\n\u003cp\u003eThe ST X uses progressive springs and a fixed damper setting chosen by ST for this car, so it is firmer than standard but still suits everyday driving. Lowering a long way or fitting low-profile tyres will firm up the ride more than the coilovers themselves.\u003c\/p\u003e\n\u003ch3\u003eDo I need an alignment after fitting?\u003c\/h3\u003e\n\u003cp\u003eYes. Changing the ride height changes camber and toe, so a full four-wheel alignment is needed once the car is at its final height, and again after any later change.\u003c\/p\u003e\n\u003ch3\u003eWill my standard wheels fit?\u003c\/h3\u003e\n\u003cp\u003eOn the original wheel sizes, ST says wheel spacers may be needed to keep enough clearance. Aftermarket wheels should be checked for clearance at your chosen ride height.\u003c\/p\u003e\n\u003ch3\u003eIs it road legal in the UK?\u003c\/h3\u003e\n\u003cp\u003eYes. It is designed for road use and comes with a German parts certificate. Keep the ride height within ST's approved range and tell your insurer about the modification.\u003c\/p\u003e\n\u003ch3\u003eWhat is the difference between ST and KW coilovers?\u003c\/h3\u003e\n\u003cp\u003eST is part of the KW group and its coilovers are made in Germany using KW engineering. ST uses galvanised steel strut housings and offers fewer adjustment options than KW's stainless steel Variant range, which keeps the price lower.\u003c\/p\u003e\n\u003ch3\u003eIs it covered by a warranty?\u003c\/h3\u003e\n\u003cp\u003eYes, ST covers it against defects in materials and workmanship. If a part ever needs replacing, contact us with your vehicle details and order number.\u003c\/p\u003e","brand":"ST Suspensions","offers":[{"title":"3-doors, Front Axle Up To 985kg","offer_id":58920096956799,"sku":"ST-132200DP","price":788.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0627\/6251\/6693\/files\/ST-Generic-341_001-1000_a6eaca0f-9933-4b56-9d8d-e84ed13e357c.jpg?v=1792770163","url":"https:\/\/coilovers.co.uk\/products\/st-x-coilovers-mini-cooper-se-f56-20-24","provider":"Coilovers.co.uk","version":"1.0","type":"link"}